Close


Results 1 to 1 of 1
  1. #1
    Administrator Dragonsys's Avatar
    Join Date
    Oct 2015
    Location
    DFW, Texas
    Posts
    636
    Rides
    4

    HowTo Bypass VATS

    Quote Originally Posted by SandmanWs7
    I have been asked many times how to bypass the VATS. I have posted on another thread that if you run into this problem that you could send me a PM. But instead of replying to ALL those who have this problem, I have decided to do a write up.

    So if a MOD would do me/us the favor of making this a sticky here, or in the proper section, that would be great.:approved:


    I decided to do it this way because I did not want to cut my VATS system. I just wanted to be able to use my car till I got it fixed. I did fix the problem the correct way later. Which is by buying a new ignition cylinder and having it installed. BUT that is a $300.00 fix at the stealership:villagers:. I was lucky to have a friend install mine for free.


    So lets begin......
    Tools Required:
    • Multimeter
    • Phillips Screwdriver
    • Solder Iron (optional)
    • Retainer Clip removal tool


    Parts Required:
    • Resister
    • Electrical Tape (reversible)
    • Solder (permanent)


    Procedure:
    1. You need to know what resistance your key has before you even begin. Your f body has 1 of 15 keys that operate your car. It is up to YOU to find out which of the 15 it is. The best way to do this yourself is to use an ohm reader and measure your key. I would recomend testing both keys (if you have both sets) to get an accurate reading. To use the ohm reader to test your key, place the readers (one should be red and the other black) on the metal chips of your key. See picture. Your ohm reader will give you a measurement. Write this down. Do the same with the other key, and write it down. If both keys are good, you should get the same reading twice. If they are different then you will need to buy two resistors, one for each key. You will have to try the bypass twice to figure out which resistor will work for you. The part you are trying to measure is the small metal piece in the black oval.


    2. Once you have the measurement go get your resistor. Price should be under 25 cents. Here are some sample resistors. Yours may be of a different color, so don't think that since yours doesn't look like this, that it is wrong. Mine was blue in color.


    Then fold the wire like this...


    3. Now time to go to your car. You will need to remove the bottom dash cover. It is held with two plastic clips and two screws (phillis head I believe). The plastic clips look like this.
    and this..
    And are located by your OBDII plug and above your E Brake. The two screw that hold it in place are further back.


    4. Disconnect your trunk release switch. This makes it easier to do what is needed in the next steps. Like this you can pull the cover off and set it in the back seat, out of the way.


    5. Now locate your wire harness that controls the VATS. It should have two wires. On set of wires has two white wires, the other side has one purple with a white line and the other one is white with a black line.


    6. Disconnect the harness.


    7. Insert your resistor thru the back side of the purple/white wire and white/black wire. There is no right or wrong way to put the resistor in. Just as long as you put one wire in each side. It should go ALL the way in. You want to be sure that the resistor touches the the wire inside.


    8.At this pioint you are basically done. Go ahead and try to turn your car on. If your car does not start, pull the resistor out. Try to put the resistor in thru the front. Make sure that you can see that you are touching both metal pieces with the resistor. Try to start the vehicle now. If it does start, then you just need to keep trying to put the resistor in better from the back. I had to try putting in the resistor in three different times to finally get it in the right way. Sometimes it feels like it is in, but it is not. If you try it from the front and it wont start then you might have a key issue. New keys run around $60.00.

    9. Once you have installed the resistor and your car did start. Use some electrical tape to keep it in place.


    10. Tuck away the wires and connect your trunk release switch. Replace the dash cover with the two screws and the plastic clips.

    Now you are done, so when ever you feel like spending the $300 or find someone to do the job for you cheaper you still have all the original wiring in place.

    This can also be used to do the remote start on your car, IF you have an automatic. Alarm stores can do this for you but will charge you close to $100.00, I know, I asked.

    This took me less than 30 minutes to do and all I spent was 8 cents on the resistor.

    Quote Originally Posted by SeVeReDiStOrTiOn
    Awesome write up:yup:


    I'll add just a little to help with the troubleshooting part. You should do this step before putting in the resistor...otherwise you'll just be wasteing your time.

    Once you disconnect the harness, put the key in the ignition and ohm check the wiring harness on the side with the two white wires.

    [thumb]http://i107.photobucket.com/albums/m309/ljasso22/WS6mama001.jpg[/thumb]

    If you get the value of the key then your problem with the VATS is somewhere else after the wiring harness...probably the BCM. The bypass won't work in this situation...

    If you don't get the value of your key then there's a open somewhere before the wiring harness...or it could be the key itself. It's common for one of those white wires to break off the ignition cylinder after years of twisting...that is more then likely your problem. Either way the bypass will work if this is your situation.


    Notes:
    • Images & procedure archived here, all credit goes to original poster (SandmanWs7) on ls1.com
    Last edited by Dragonsys; 10-11-2016 at 01:48 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •